© 2018 by Analytical and Control Technology 2000 Co., Ltd.

  • Facebook Social Icon
  • Twitter Social Icon
  • Google+ Social Icon
Level & Density Measurement
> Non-Invasive Tank Level Gauge (1 TANK)
  • Used extensively across Oil & Gas, Beverage,Chemical, Refrigeration and Pharmaceutical industries

  • Truly non-invasive sensing technique

  • Sensors bonded to outside of tank

  • Fits tank of most shapes and sizes

  • Output to Telemetry system - various options

  • Low cost, reliable & accurate tank gauging

  • Not affected by pressure

 

> Non-Contact Tank Level Gauge (1 TANK) for Hazardous Areas
  • Approved for hazardous area

  • Used extensively across Oil & Gas, Beverage,Chemical and Pharmaceutical industries

  • Truly non-invasive sensing technique

  • Transceiver bonds to outside of tank

  • No tank break-in

  • Easy installation

  • Ambient temperature compensated (temperaturemeasurement in display unit)

> Non-Invasive Tank Level Measurement System (2 TANKS)
  • Level measurement for 2 tanks

  • Truly non-invasive technique

  • Sensors bonded to outside of tank base and side wall

  • 20 point calibration table

  • 4 - 20mA / 1.5 V analogue outputs

  • RS485 / 232 Modbus serial communications

  • ATEX/ IECEx approved sensors for hazardous areas available

  • Optional local display keypad

> Non-Invasive Tank Level Measurement System (4 TANKS)
  • Level measurement for up to 4 tanks

  • Truly non-invasive sensing technique

  • Sensors bonded to outside of tank base and sidewall

  • 20 point calibration table

  • 4 - 20mA/ 1 - 5V analogue outputs

  • RS485 / 232 Modbus serial communications

  • ATEX / IECEx approved sensors for hazardous areas available

  • Optional local display & keypad

  • Fast, reliable and accurate tank contents measurement

> SMARTLevel - Remote Ultrasonic Non-Invasive Tank Level
   Measurement
  • Data is viewed on a secure Internet portal

  • Main power supply 24 Vdc

  • 2G/3G Mobile communications

  • 4G upgradable

  • On board self-diagnostics

  • Simple to install

  • Interfaces to new & existing VesselCheck products

> Non-Invasive Point Level Detector for Tanks & Pipes
   (Hi-Lo Alarm)
  • Non-invasive liquid level switch for use inapplications where avoiding contact is vital

  • Uses ultrasonic

  • Sensor is clamped externally to the wall of thepipe or vessel

  • Enables tank high / low level alarm

  • Response time of 1 second

> Multi-measurement Controller & Analyser
  • Cavitation Elimination

  • Preventing flashing in liquid flows

  • Choked flow in gases

  • Noise/Vibration Reduction

  • Permanent Pressure Reduction

  • Feed & Vent Flow

  • Pressure drop

> Carbon Dioxide Measurement
  • Most common and widely used differential pressure producer

  • Suitable for a wide range of flow restriction measurementapplications in line sizes of 50mm and above

  • Wide range of materials including exotics such as monel,hastelloy, as well as ceramic

  • Orifice sizing on request

  • Proven technology

  • Range of Orifice Types- Concentric Square Edge- Conical Entrance- Quarter Circle- Segmental- Eccentric

> Oxygen Measurement
  • Designed for hygienic applicationsto measure dissolved oxygencontent (DO2) reliably andaccurately

  • Uses photodiode technology

  • Measurement range from 4ppm to25ppm (0.05% - 300% saturation)

  • Low maintenance required

  • Electrolyte free and no fragilemembrane

  • Quick response and not affected byflow rate

  • Integrated RS485 Modbus RTUinterface

> Liquid Concentration Sensor & Transmitter
  • Economic measurement of liquid concentration and density through use of ultrasound technology

  • Available as non-invasive and invasive formats

  • ATEX hazardous area approved

  • Zero drift and no re-calibration

  • No moving parts

  • Lower installation and maintenance costs

  • Increased process efficiency

  • Improved quality monitoring

  • High accuracy and repeatability